DNP Embedded Module with ARM and Linux      Order Code: ADNP-9200      Price: $308.00

The DIL/NetPC ADNP/9200 provides a very compact Atmel 180 MHz AT91RM9200 ARM9-based low power embedded controller with USB support, TCP/IP stack, web server, Telnet server, (T)FTP support for embedded networking with Ethernet, USB and WSN (Wireless Sensor Network) connectivity in industrial and laboratory environments. The ADNP/9200 offers the footprint of a 128-pin QIL (Quad-In-Line) socket with 2.54 mm centers (0.1 inch pin grid) and the hardware and software features necessary to add embedded networking capabilities to any product design. The ADNP/9200 was developed specifically for products which need to be connected to 10/100 Mbps Ethernet-based TCP/IP networks and wireless sensor networks (gateway applications) with minimum development costs.

The ADNP/9200 comes as ready-to-run embedded networking system for Ethernet und WSN (Wireless Sensor Network) gateway applications. The use of the ADNP/9200 will allow you to realize substantial time and costs savings over other chip-based approaches. Currently, there is no other embedded networking solution with pre-installed O/S, WSN expansion, USB host/device, 10/100 Mbps Ethernet- and TCP/IP-based and more development time saving features on the market. There is also no faster Time-to-Market for your product with lower costs if USB host/device, 10/100 Mbps Ethernet, full TCP/IP and a embedded Web server or other TCP/IP-based server software are required.

• Atmel AT91RM9200 32-bit ARM9 MCU with 180 MHz Clock Speed
• 200 MIPS @ 180 MHz
• 64 Mbyte 32-bit SDRAM Memory
• 32 MByte FLASH Memory
• Two 10/100 Mbps Ethernet Interfaces
• Two USB Host Ports (full-speed and low-speed)
• One USB Device Port (full-speed and low-speed)
• One Serial Peripheral Interface (SPI)
• Three Serial Ports (one with all handshakes)
• 20-bit General Purpose high-speed Parallel I/O
• 16-bit I/O Expansion Bus
• ESL (Expansion Sandwich Layer) connector for WSN (Wireless Sensor Network) expansion
• 1 Interrupt Inputs, 4 Chip Select Outputs
• Programmable Watchdog Timer
• JTAG IEEE 1149.1 Test Interface
• In-System Programming Features
• 128-pin JEDEC QIL-128 Connector, 2.54 mm Centers
• 3.3 Volt Low Power Design, Supply Voltage 3.3 VDC (+- 5%)
• Supply Current 300 mA typ. @ 180 MHz
• 0 °C to +70 °C Operating Temperature
• Size 82 mm * 36 mm

To interface the ADNP/9200 with existing devices and equipment, the ADNP/9200 offers three asynchronous serial RS232C ports with TTL levels (COM1 with handshake signals, COM2 only TxD and RxD, COM3 only TxD and RxD - available over expansion sandwich layer), one USB device port, two USB host ports (compliance with USB 2.0 full-speed and low-speed specification), two 10/100 Mbps Ethernet interfaces, 20-bit general purpose high-speed parallel I/Os, ESL (Expansion Sandwich Layer) connector for WSN expansion and a 16-bit extension bus with interrupt input and chip select outputs. There are two ways for ADNP/9200 integration: 1. Adapt the ADNP/9200 to your existing product. Use the existing I/Os within your product to communicate with the ADNP/9200. 2. Use the ADNP/9200 to control and monitor the hardware of your existing product. This might enable you to replace your existing controller entirely. In a new product design, the ADNP/9200 can be the main controller. Additional I/Os are driven by the 16-bit extension bus and the ESL connector.

The on-board FLASH memory provides storage for the ADNP/9200 operating system with USB driver code, TCP/IP stack and embedded web server as well as OEM applications and data. The FLASH memory is in-system programmable over JTAG, serial and Ethernet interfaces. The boot block of the FLASH memory is only in-system programmable over the JTAG interface through a special cable attached to a PC parallel port. For all other FLASH blocks, you can use also a high-speed serial connection through the ADNP/9200 COM1 port or the 10/100 Mbps Ethernet interfaces for in-system programming. The ADNP/9200 in-system programming was developed for OEM application software, operating system download (i.e. upgrade the embedded Linux O/S) and data download and also to make it easier to update the on-board FLASH content in the field.

Starter Kit for ADNP/9200 Embedded Module