Selected Product: Programmers/Burners/Hand Held Programmers/PIC Handheld Programmers/PIC-HH0020
PIC Handheld Programmer - Parallel Port Order Code: PIC-HH0020 Price: $99.00
Individual Hand Held Programmer for PIC Microcontrollers
HandHeld Field and Production Programmer for PIC microcontrollers, with 128 KB of memory. Just load the programmer from a PC using the PIC Hand Held programmer Starter Kit. Now you just plug it into your target board and program and verify Code, Data, User ID and Configuration Bytes with a single button press. It can power your target PIC microcontroller using internal battery or 9V external Power supply.
This PIC programmer is ideal for non-technical operatives as no mistakes can be made - just press the button and the correct code MUST be loaded. You can set it to program the whole PIC microcontroller or just the Data memory (PIC16F only). It supports PIC16F and PIC18F microcontrollers.
Now supports PIC18FxxJxx devices
This programmer has parallel port firmware loaded. If used with USB PC interface, the software will ask to carry out a firmware update. Just agree and it will convert to a USB firmware.
Features
PIC Microcontroller Support
All released PIC18F microcontrollers including PIC18FxJx. Updates available for new device support.
PIC16F Microcontrollers
You will need a Starter Kit to load this programmer. One Starter Kit will allow you to load as many PIC Hand Held Programmers as you want. The Starter kit comes complete with one PIC Hand Held Programmer and is on Special Offer.
PIC Handheld Programmer Starter Kit
If you do not want to use the internal 9V PP3 battery, the power supply required is 9V with a 2.5mm Barrel connector. These are available on the shop.
9V International Power supply for use with this PIC programmer.
A Quick start guide with recommended circuits and setup details can be downloaded here.
datasheet | support information
These open in a new window.
HandHeld Field and Production Programmer for PIC microcontrollers, with 128 KB of memory. Just load the programmer from a PC using the PIC Hand Held programmer Starter Kit. Now you just plug it into your target board and program and verify Code, Data, User ID and Configuration Bytes with a single button press. It can power your target PIC microcontroller using internal battery or 9V external Power supply.
This PIC programmer is ideal for non-technical operatives as no mistakes can be made - just press the button and the correct code MUST be loaded. You can set it to program the whole PIC microcontroller or just the Data memory (PIC16F only). It supports PIC16F and PIC18F microcontrollers.
Now supports PIC18FxxJxx devices
This programmer has parallel port firmware loaded. If used with USB PC interface, the software will ask to carry out a firmware update. Just agree and it will convert to a USB firmware.
Features
- PIC Hand-held programmer uses 9V PP3 battery or power supply
- Single button operation
- Load it once, program targets for ever
- Reload new programs as often as you need
- Holds program code indefinitely
- Low or High Voltage programming
- 10-way DIL and 6 x 1-way flying lead connectors included
- Program/Verify Flash or EEPROM or both
- Programs and Verifies Configuration words
- Existing EEPROM data can be preserved
- Powers target PIC device (up to 150mA) at 5V regardless of target voltage (so that Bulk Erase command always works)or can be powered from target
- Dimensions: Metric- 106mm x 58mm x 25mm
- Dimensions: Imperial - 4.5 x 2.5 x 1 inches
PIC Microcontroller Support
All released PIC18F microcontrollers including PIC18FxJx. Updates available for new device support.
PIC16F Microcontrollers
- PIC16F627
- PIC16F628
- PIC16F627A, PIC16F628A, PIC16F648A (HVP mode programming only if Reset pin is not reprogrammed as I/O)
- PIC16F636, PIC16F639, PIC16F684, PIC16F688
- PIC16F7x
- PIC16F7x7
- PIC16F785
- PIC16F818
- PIC16F819
- PIC16F8x
- PIC16F8xA
- PIC16F87x
- PIC16F873A
- PIC16F874A
- PIC16F876A
- PIC16F877A
- PIC16F88x
- PIC16F91x
- PIC16F630
- PIC16F676
- PIC16F716 - will be supported
- PIC16F5x - will be supported
- PIC16F505
You will need a Starter Kit to load this programmer. One Starter Kit will allow you to load as many PIC Hand Held Programmers as you want. The Starter kit comes complete with one PIC Hand Held Programmer and is on Special Offer.
PIC Handheld Programmer Starter Kit
If you do not want to use the internal 9V PP3 battery, the power supply required is 9V with a 2.5mm Barrel connector. These are available on the shop.
9V International Power supply for use with this PIC programmer.
A Quick start guide with recommended circuits and setup details can be downloaded here.
datasheet | support information
These open in a new window.
Product Accessories
 Batteries for Handheld Programmer |  9V International Wall Transformer |  PIC Handheld Programmer Starter Kit - Parallel |
