Handheld PIC Programmer - USB firmware

Individual Hand Held PIC Programmer for PIC Microcontrollers

Replaced by New version - PIC-HH0120

Please Purchase new version

---

HandHeld Field and Production PIC Programmer for PIC microcontrollers, with 256 KB of memory. Just load the Handheld PIC Programmer from a PC using the Hand Held PIC Programmer USB Starter Kit. Now you just plug it into your target board and program and verify Code, Data, User ID and Configuration Bytes with a single button press. It can power your target PIC microcontroller using internal battery or 9V external Power supply.

This Handheld PIC Programmer is ideal for non-technical operatives as no mistakes can be made - just press the button and the correct code MUST be loaded. You can set it to program the whole PIC microcontroller or just the Data memory (PIC16F only). It supports PIC16F and PIC18F microcontrollers.
Now supports PIC18FxxJxx and K PIC microcontrollers.

---

This Handheld PIC Programmer has USB port firmware loaded. If used with parallel PC interface, the software will ask to carry out a firmware update. Just agree and it will convert to a parallel port firmware version.

---

Handheld PIC Programmer Features

• PIC Handheld Programmer uses 9V PP3 battery or power supply
• Single button operation
• Load it once, program targets for ever
• Reload new programs as often as you need
• Holds program code indefinitely
• Low or High Voltage programming
• 10-way DIL and 6 x 1-way flying lead connectors included
• Program/Verify Flash or EEPROM or both
• Programs and Verifies Configuration words
• Existing EEPROM data can be preserved
• Powers target PIC device (up to 150mA) at 5V regardless of target voltage (so that Bulk Erase command always works)or can be powered from target
• Dimensions: Metric- 106mm x 58mm x 25mm
• Dimensions: Imperial - 4.5 x 2.5 x 1 inches
• 256KB memory

---

PIC Microcontroller Support
All released PIC18F microcontrollers including PIC18FxJx. Updates available for new device support.

PIC16F Microcontrollers

• PIC16F627
• PIC16F628
• PIC16F627A, PIC16F628A, PIC16F648A (HVP mode programming only if Reset pin is not reprogrammed as I/O)
• PIC16F631, PIC16F636, PIC16F639
• PIC16F677
• PIC16F68x, PIC16F690
• PIC16F7x
• PIC16F7x7
• PIC16F785
• PIC16F818
• PIC16F819
• PIC16F8x
• PIC16F8xA
• PIC16F87x
• PIC16F873A
• PIC16F874A
• PIC16F876A
• PIC16F877A
• PIC16F88x
• PIC16F91x

Note: Not all devices have LVP mode Not supported

• PIC16F630
• PIC16F676
• PIC16F716 - will be supported
• PIC16F5x - will be supported
• PIC16F505

---

You will need a Starter Kit to load this Handheld PIC Programmer. One Starter Kit will allow you to load as many Hand Held PIC Programmers as you want. The Starter kit comes complete with one Handheld PIC Programmer and is on Special Offer.
Handheld PIC Programmer USB Starter Kit

---

If you do not want to use the internal 9V PP3 battery, the power supply required is 9V with a 2.5mm Barrel connector. These are available on the shop.
9V International Power supply for use with this PIC programmer.

---

A Quick start guide with recommended circuits and setup details can be downloaded here.

---

For an overview of our PIC Programmer range, please see PIC Programmer Overview in new window

---